Raider Truck Caps Replacement Hardware & Parts
Our complete hardware replacement kit includes everything you need to restore your Raider truck cap to factory-fresh condition. Each kit contains eight heavy-duty clamps, stainless steel mounting bolts, weather seals, and installation hardware sized specifically for your Raider model.
Whether you're replacing worn components or upgrading after years of daily use, this kit ensures a secure, weatherproof seal between your cap and truck bed. We've packaged the exact hardware our factory installers use, so you get the same quality and fit as the day your cap was first mounted.
- Eight heavy-duty powder-coated clamps with reinforced spring tension
- Complete stainless steel bolt set (corrosion-resistant grade 304)
- Two 8-foot EPDM rubber seal strips for bed rail contact points
- Foam weatherstripping for front bulkhead seal (48 inches)
- Four aluminum mounting brackets with pre-drilled holes
Materials & Construction Standards
Every component in our raider truck caps replacement parts lineup meets the same manufacturing standards we apply to complete cap assemblies. Clamps are stamped from 12-gauge steel and powder-coated with a two-stage process that bonds the finish at the molecular level, preventing chips and corrosion even when exposed to road salt and harsh UV.
Stainless steel fasteners are grade 304, the same marine-grade alloy used in coastal applications where corrosion resistance is critical. EPDM rubber seals are extruded to exact dimensions, then cut to length in our facility to ensure consistent compression characteristics across the entire seal surface.
Installation & Torque Specifications
Clamp Installation
Position each clamp so the mounting holes align with the pre-drilled holes in your cap’s mounting rail. Thread stainless steel bolts through the clamp body and into the rail, then hand-tighten until the clamp contacts the truck bed rail. Use a torque wrench to tighten each bolt to 15 ft-lbs in a cross-pattern sequence — this ensures even pressure distribution and prevents warping.
Seal Replacement Process
Remove old weatherstripping by peeling it away from the mounting channel, then clean residual adhesive with isopropyl alcohol. Measure and cut new seal strips to length, leaving a 1/4-inch overlap at corners. Peel the adhesive backing and press the seal firmly into the channel, starting at one end and working toward the other to avoid air bubbles.
Compatibility Across Raider Models
Our hardware kits are engineered to fit every Raider truck cap model we’ve manufactured since 2010, including both fiberglass and aluminum constructions. The clamp hole spacing and bolt thread pitch remain consistent across our entire product line, so you can confidently order replacement parts without verifying year-specific details.
For caps manufactured before 2010, contact our customer service team with your cap’s serial number (located on the front interior panel). We maintain archived specifications for legacy models and can supply compatible hardware even for discontinued designs.
Essential Hardware & Seals for Every Raider Cap
What people are saying
Replacement Parts Questions
All Raider hardware kits and seals manufactured since 2010 are standardized across our entire product line. You only need to know your truck bed length (short bed 5.5-6.5 feet or long bed 8 feet) to select the correct seal kit. Clamps and hardware are universal across all Raider models.
For caps made before 2010, locate your cap's serial number on the interior front panel and contact our customer service team. We maintain compatibility records for every cap we've manufactured and can verify which replacement parts work with your specific model.
You can replace individual clamps using our four-pack clamp set. Many customers replace just the clamps that show visible rust or have lost clamping tension while leaving functional clamps in place.
We recommend the complete hardware kit if your cap is more than seven years old, if you're experiencing water leaks at multiple points, or if you're installing the cap on a different truck. The kit ensures all components are fresh and properly matched.
Bed rail seals generally need replacement every 3-4 years under normal conditions. Bulkhead seals often last 5-6 years because they receive less direct UV exposure.
Factors that accelerate seal degradation include extreme temperature swings, frequent exposure to road salt, and constant direct sunlight when the truck is parked outdoors. If you notice water intrusion, increased wind noise, or seals that no longer compress and spring back when pressed, it's time to replace them regardless of age.
We strongly recommend using the stainless steel bolts included in our replacement kits. Standard zinc-plated bolts corrode quickly when exposed to road salt and moisture, and corroded bolts can seize in the mounting holes or snap during removal.
Stainless steel fasteners resist corrosion even in harsh conditions and maintain consistent torque over time. The grade 304 alloy we use is the same material specified for marine applications where salt exposure is constant.
For clamp installation, you'll need a socket wrench set, a torque wrench capable of measuring 15 ft-lbs, and Phillips or flathead screwdrivers depending on your cap model. The complete hardware kit includes all necessary bolts and washers.
Seal installation requires no tools — just isopropyl alcohol for surface cleaning, a utility knife or scissors to cut seals to length, and a clean cloth. The self-adhesive backing eliminates the need for separate adhesives or fasteners.
Installing genuine Raider replacement parts does not void your cap warranty. In fact, using our OEM hardware and seals helps maintain warranty coverage by ensuring components meet our original specifications.
Using third-party or universal-fit parts may affect warranty claims if those components cause damage to the cap structure. We recommend sticking with genuine Raider parts to preserve full warranty protection.
Most truck owners with basic mechanical skills can install clamps and seals in 30-60 minutes using common hand tools. Our instruction sheets include step-by-step guidance, torque specifications, and troubleshooting tips.
If you're uncomfortable working with hand tools or don't have access to a torque wrench, any truck accessory shop or automotive service center can install these components. The labor typically costs $50-100 depending on your location.